Job Details

P&C Technician II - P&C Technician Sr.

Perform work associated with the installation, operation, testing, and maintenance of all protection and control devices and related equipment under direct, immediate, or general supervision. Such devices and equipment include but are not limited to digital relays, electromechanical relays, intelligent electronic devices, station disturbance recorders (SDR), digital fault recorders (DFR), oscillographs and event recorders, RTU's and station SCADA systems, statistical load metering, telemetering and transducers. Additionally, install, maintain, and operate all power line carriers (PLC), tone, pilot wire, fiber, and associated P&C communications equipment. Respond to emergency call-outs and coordinate prompt restoration of service to customers as required. This list is not intended to limit assignment of work or the degree of supervision under all operating conditions. Employee may perform miscellaneous, related, and incidental work in addition to that specifically outlined below.

Assist in the performance of acceptance and installation tests on protection, control, and measurement devices and associated equipment in stations.

Assist in the installation, maintenance, and operation of all power line carriers, station SCADA, and associated communications equipment or cables as assigned.

Perform switching under direct supervision of qualified personnel following direction of the proper operating authority.

Assist in the installation, maintenance, and operation of any new and added equipment or systems as assigned.

Maintain test equipment and automotive equipment in good working order so that work can be performed safely and efficiently anywhere throughout the System.

Prepare and maintain accurate records, reports, and drawings as required.

Assist employees of equal or higher classification.

Perform all duties in accordance with the Companys safety rules and operating regulations, NERC and environmental compliance, and practices.

Perform similar or less skilled work as assigned.

Test protection & control devices and equipment periodically and as required.

Calibrate protection & control devices and equipment on a pre-established schedule and as required.

Assist with diagnosis of trouble, mis-operation, or damage of equipment and assist with corrective action to affect repair and prevent recurrence.

Operate a computer device to test, calibrate, and retrieve data from protection & control devices.

P&C Technician II: (Start $30.12, $31.24, $32.32, $33.49- increase every 6 months, until reach top level, then move to next classification in job family)

Education requirements are listed below: Associate's degree in electrical engineering technology, electronic technology, or related technology field.

Work Experience requirement listed below: No previous work experience required.

P&C Technician I: (Start $34.99, $36.16, $37.33, $38.49- increase every 6 months, until reach top level, then move to next classification in job family)

Education requirements are listed below: Associate's degree in electrical engineering technology, electronic technology, or related technology field.

Work Experience requirement listed below: Minimum of 24 months satisfactory work experience as a P&C Technician II or the equivalent (as determined by the Company through demonstration, examination, and performance appraisal).

P&C Technician Sr.: (Start $40.29, $41.82, $43.30, $56.97- increase every 6 months, until reach top level)

Education: Associate's degree in electrical engineering technology, electronic technology, or related technology field

Experience: Minimum of 24 months satisfactory combined work experience as a P&C Technician I or P&C Technician I Certified or the equivalent (as determined by the Company through demonstration, examination, and performance appraisal).

These are additional expectations for the job and could include specific work experience, license/certifications, preemployment testing, expectations about travel, shift work, etc.:

Must satisfactorily complete, in such time frames as may be established by the Company, the qualifications necessary to perform the duties of the next higher classification in the line of progression or vacate the current classification.

Must have the ability and desire to acquire the necessary knowledge and skills to perform the duties and/or responsibilities of the key job (P & C Technician Sr in this family and be qualified through demonstration, examination, and/or performance appraisal as determined by the Company).

Must possess and maintain a valid state driver's license and must meet all vehicle operation requirements as designated by federal and/or state law.

Considerable travel and overtime may be required to complete work assignments.

Must successfully complete Physical Abilities Test (PAT)

Competencies

Technical Proficiency

Possesses technical knowledge acquired from an Associate Degree in Electrical/Electronic Engineering Technology.

Gains knowledge of standards, codes, and regulations relevant to area of assignment.

Gains knowledge with pertinent equipment, material, systems, and business processes.

Assists employees in handling defined portions of routine problems when beneficial to AEP.

Possesses basic computer literacy, knowledge, and skills.

Leadership and Guidance

Performs work activities as assigned and coached by higher level employees.

Demonstrates ability to work with others in supplying information and seeking assistance as necessary.

Planning and Organization Ability

Plans work in accordance with AEP standard planning practices.

Prioritizes routine work to meet the demands of the company.

Maintains accurate records.

Problem-Solving and Initiative

Applies technical knowledge and experience in resolving problems encountered in assigned work.

Uses initiative in looking for opportunities to improve the process and increase job knowledge/technical skills.

Seeks out, compiles, analyzes, and interprets information necessary to perform work activities and solve problems.

Communication and Interpersonal Skills

Communicates effectively, both orally and in writing with internal and external customers.

Assists in the preparation of technical reports and papers.

Demonstrates the ability to be a team player.

Relates to people in an open, friendly, and sincere manner.

Decision Making and Business Awareness Characteristics

Develops decision-making skills based on sound judgment and job knowledge.

Develops an understanding of the roles and responsibilities of the local organizational unit.

Physical Demands:

List any physical demands required for position Minimum Requirement P&C Technician/Electrician Amount of Weight Lifted from Floor/Ground to Waist Level 60 Amount of Weight to be Carried for 20 Feet 50 Amount of Weight Lifted to Chest Level 30 Amount of Weight Lifted to Eye Level 30 Distance to Walk Accumulated over the Course of an 8-Hour Shift 1 Mile Distance in Feet to Climb and Work on a Ladder/Structure 20 and Higher Distance in Feet to Ascend to and Work in a Bucket/Lift 100 and Higher (Tested at 60') Ability to Discriminate between Colors Yes (Tested)